Bryant 453 Betriebsanleitung PDF herunterladen (Seite 5)

Lighting and Operating Instructions

Lighting Instructions: Gas

Operation

1. Make certain that 12 Volts DC

is available to the refrigerator.

2. Turn on gas supply at the tank.

3. Set thermostat control to the

maximum cold setting.

4. Set ignitor switch to "ON" posi-

tion. The light located on the

switch will illuminate if 12 volts

DC is present.

5. Push and turn the "ELEC-OFF-

GAS" control counter-clockwise

so that knob indicator points to

"GAS". Push the control knob

and hold it until the flame indi-

cator illuminates (continuous

glow). Continue to hold approxi-

mately 5 seconds, then release.

The flame indicator will remain

on. If not, repeat this step.

Note:

The flame should ignite within 10

seconds. On initial refrigerator start-

up, it may take longer than 10 sec-

onds to allow air to be purged from

the gas line, as indicated by the

flame indicator failing to illuminate.

DO NOT HOLD GAS CONTROL

VALVE IN MORE THAN 30 SEC-

ONDS. IF FLAME IS NOT INDI-

CATED WITHIN THIS TIME, TURN

GAS TO "OFF", WAIT 2 MINUTES

AND RETRY. FAILURE TO DO SO

CAN CAUSE GAS TO BUILD UP IN

BURNER AREA AND RESULT IN AN

EXPLOSION WHICH CAN CAUSE

PERSONAL INJURY OR DEATH.

6. Move thermostat control to de-

sired setting.

7. The ignitor switch should be

left in the "ON" position during

gas operation. If the switch is

turned off, the refrigerator will

cycle normally. However, in

case of flame blowout, the re-

lighter does not function.

Start-Up Instructions : AC Electric Operation

1. Make certain that 120 Volts AC is available to the refrigerator.

2. Set the thermostat control to desired setting.

3. Set "AC-DC" switch to "AC" position (3-Way models only).

4. Set ignitor switch to "OFF" position.

5. Push and turn the "ELEC-OFF-GAS" Control clockwise so that knob in-

dicator points to "ELEC". Upon release, note that the knob moves to-

ward you, indicating that the control is locked into electric position.

Start-Up Instructions: DC Electric Operation (3-Way only)

1. Make certain that 12 Volts DC is available to the refrigerator.

2. Set thermostat control to desired setting.

3. Set "AC-ELECTRIC STANDBY-DC" switch to "DC" position.

4. Set ignitor switch to "OFF" position.

5. Push and turn the "ELEC-OFF-GAS" control clockwise so that knob indi-

cator points to "ELEC". Upon release, note that the knob moves toward

you, indicating that the control is locked into electric operation.

Operation Note:

Use the "ELEC-OFF-GAS" control to shut off all cooling operation (both

Gas and Electric). The "GAS IGNITOR" switch must be shut off inde-

pendently to prevent unnecessary sparking.

On 3-Way models, use the "ELECTRIC STANDBY" position of the "AC-ELEC-

TRIC STANDBY-DC" switch to temporarily shut off AC or DC operation.

Operation Shut-Down: All Modes

1. Set ignitor switch to "OFF" position.

2. Push and turn "ELEC-OFF-GAS" control to "OFF".

Figure 3.4 2-Way Controls (Upper), 3-Way Controls (Lower)

WARNING

B101

3-5

1 2 3 4 5 6 7 8 9 10 ... 30 31

Kommentare zu diesen Handbüchern

Keine Kommentare

Bryant 453 Betriebsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Bryant 453